![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Left_Top.gif) |
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif) |
![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Right_Top.gif) |
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif) |
Overview
The Seelevel 709-BTP7 Bluetooth monitor can be used to replace any existing 7 tank 709 system or as an added monitor to a Garnet 709-BTP7 SeeLevel II System. Designed for accurate level measurement of RVs, motorhomes, and trailers with three holding tanks. This system monitors battery voltage, fresh, grey, and black water levels as well as the LPG tank. The level in percent is shown on a three-digit LED display. This model includes a 3-way pump switch with a connector that allows for more wiring options.
Note: This is the monitor only.
Features
- App is available for any compatible Android and Apple iOS device.
- Download the Garnet SeeLevel app in Google Play Store or Apple App Store
- Reason for ordering Monitor Only
- As a second console to be installed outside by the holding tanks.
- Upgrade existing 709 system with Bluetooth capabilities
- Replace damaged unit
- Provides accurate tank level information using a percentage of full readout.
- Uses common industry connector for ease of installation and servicing.
- Includes: (1) SeeLevel 709 monitor and connector assembly/pigtail
- Limited 1-year manufacturer warranty
NOTE: If you already have a Garnet Seelevel II (see list of models below), you can upgrade to the Bluetooth model by just buying the BTP3 monitor only! All you will need to do is remove the pigtail and hardwire the Bluetooth monitor to your current system.
- 709-2P, 709, 709-P3, 709-P3W or 709-HP3W.
- Note: Replacing the HP3W model with the BTP7, you will lose the hot water tank switch.
Specifications
- Display requires 12 volts from the RV battery, the system will function from 11 volts to 16 volts
- Accuracy: +/- 8% or better, limited by resolution and tank height and shape.
- Current drain is less than 200mA
- Panel Dimensions: 4" W x 2.8" H x 1" D
- Required Cutout Size: 3" W x 1.8" H.
- Weight: 1 lb.
Instructions
Garnet 709-BTP7 SeeLevel II Tank Monitor with Bluetooth - Monitor Only
Seelevel Bluetooth Monitor
|
|
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif) |
![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Left_Bottom.gif) |
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif) |
![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Right_Bottom.gif) |
![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Left_Bottom.gif) |
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif) |
![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Right_Bottom.gif) |
![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Left_MidDiv.gif) |
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif) |
![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Right_MidDiv.gif) |
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif) |
Additional Product Information
Display Mounting Panel: Black panel, approximately 4" wide by 2.8" high by 1" thick (102mm wide X 71mm high X 25mm thick). Panel screws to the wall.
System Power Requirements: Display requires 12 volts from the RV battery, the system will function from 11 volts to 16 volts. Current drain is less than 200mA.
Wiring: A single two-wire conductor required from the display to the senders. All the senders are wired in parallel. 12 V power and ground required for display. A separate two-wire conductor required from the display to the LPG sender.
LPG: Display will work with an LPG sender with a maximum resistance of 50 ohms to 500 ohms. Display shows increasing level as resistance increases. System must be calibrated with the LPG tank full.
|
|
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif) |
![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Left_Bottom.gif) |
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif) |
![](/v/vspfiles/templates/rvup2021/images/DBox_Border_Right_Bottom.gif) |
![](/v/vspfiles/templates/rvup2021/images/clear1x1.gif)
|